United-states-stove-company 1200Q Manuel d'utilisateur

1•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•Model 1200QSOLID FUEL WARM AIR FURNACEOwners ManualCOMPANYUNITEDSTATESSTOVECSSUWARNOCK HERSEYR*FOR PARALLEL

10•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•ASSEMBLY OF FURNACEYour furnace requires the following itemsto be assembled or installed by the servicepers

11•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•BLOWER & COMPONENT ASSEMBLY - FIG. 11JUNCTION BOXMOUNTINGBRACKET1. Attach the Honeywell Limit Control t

12•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•MODEL 1200Q WIRING DIAGRAM - FIG. 12LIMIT CONTROLBLACKWHITEWHITEBLACKWHITEBLACKGREEN2 x 4 JUNCTION BOXBLOWE

13•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•InstallationPlease see all methods of Installationin Appendix at the rear of this booklet. This is a fur

14•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•POWER FAILURE INSTRUCTIONS:Operation after loss of powerRemove filter if provided.Do not expect to keep hom

15•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•CENTRAL INSTALLATION (U.S. & CANADA)ADD-ON INSTALLATION (U.S. ONLY)

16•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•ALTERNATIVE PARALLEL INSTALLATION WIRING DIAGRAM - FIG. 15TO GAS/OIL/ELECTRICTRANSFORMERHOTBLASTCOMBINATION

17•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•Your Hotblast Furnace is for burning wood only.WOOD BURNING: (1)use Hardwood, 18" to 26", split

18•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•Do not expect a furnace to draw. It is the chimney thatcreates the draft. Smoke spillage into the house or

19•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•MODEL 1200Q - PARTS

2•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•TOOLS AND MATERIALS NEEDEDTOOLSPencil6 Foot Folding Rule or TapeTin SnipsDrill, Hand or ElectricDrill Bit (F

20•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•MODEL 1200Q - PARTS LISTKEY PART# DESCRIPTION QTY.1 69121 FIREBOX WELDMENT 12 24576 BAFFLE 13 40288 GRATE 4

21•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•APPENDIXINSTALLATION ANOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIREDFOR THIS INSTALLATION.

22•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•APPENDIXINSTALLATION BNOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIREDFOR THIS INSTALLATION.

23•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•APPENDIXINSTALLATION CNOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIREDFOR THIS INSTALLATION.

24•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•APPENDIXINSTALLATION D(U.S. ONLY)INSTALLATION E(U. S. ONLY)

25•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•APPENDIXINSTALLATION FINSTALLATION G

26•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•NOTES

27•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•List of Problems Possible Cause Solutions1. Smoking when feed door is open.2. Furnace does not heat.3. Blow

28•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPEND-ABLE SERVICE FROM YOUR HOTBLAST FURNACE, AND EN-ABLE YOU

3•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•CAUTION:Your Furnace has the following labels. Read and obey all labels.REFER TO MARKINGS ON THE APPLIANCE F

4•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•Read these rules and the instructions carefully. Failure to follow them will cause a hazard that could resul

5•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•Your Supplemental Furnace is designed to bea supplemental or central heating source for yourhome. This solid

6•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•MODEL 1200Q DIMENSIONSFIG. 1

7•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•1.2.3.4. FIG. 3The furnace should be located in the sameroom as the central system and as close aspossible,

8•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•LISTED FACTORY BUILT CHIMNEYCarefully follow chimney manufacturer's instructions. Use only a Listed Res

9•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•RULES FOR CONNECTOR PIPE INSTALLATION FIG. 6The crimped end of the chimney connectorfits inside the furnace